欢迎访问厦门雄霸电子商务有限公司(漳州分公司)官网!

全国咨询热线

18059884797

产品中心
您的位置:首页 >> 产品展示 >> Vibro-meter

Vibro-meter VM600 IOC16T 输入输出卡 通过连接器P2,使用工业包(IP)接口

品牌:Vibro-meter

型号:VM600 IOC16T

名称:输入输出卡

质保:一年
联系电话:18059884797

详细介绍


VM600 IOC16T   输入输出卡


I0C4T输入/输出卡作为来自梅吉特振动计国产品线的VM600系列MPC4机械保护卡的信号接口。安装在VM600机架的后部,通过两个连接器直接连接到机架背板上。每个IOC4T卡都与相应的MPC4卡相关联,并直接安装在VM600机架(ABE04x或ABE056)的后面。I0C4T工作在从属模式,并与MPC4通信,通过连接器P2,使用工业包(IP)接口。I0C4T的前面板(VM600机架的后部)包含端子带连接器,用于连接来自测量链(传感器和/或信号调节器)的传输电缆。螺纹端子连接器也用于从任何外部控制系统输入所有信号并输出所有信号。I0C4T卡具有所有输入输出防电磁F扰和浪涌保护功能,同时满足EMC (electromagnetic compatibility)标准。I0C4T将原始动态(振动)和速度信号从传感器连接到MPC4。这些信号,一旦处理,被传递回IOC4T, 并在其前面板(VM600的后方)的终端带上可用。对于动态信号,四个板载数模转换器(dac)提供0至10 V范围内的校准信号输出。此外,四个板载电压电流转换器允许信号作为电流输出在4至20 mA(跳线可选)范围内提供。
Vibro-meter    VM600 IOC16T   输入输出卡    通过连接器P2,使用工业包(IP)接口

The I0C4T input/output card serves as the signal interface for the VM600 series MPC4 mechanical protection card from the Meggitt vibration meter domestic product line. Installed at the rear of the VM600 rack and directly connected to the rack backplane through two connectors. Each IOC4T card is associated with the corresponding MPC4 card and installed directly behind the VM600 rack (ABE04x or ABE056). I0C4T operates in slave mode and communicates with MPC4 through connector P2 using the Industrial Packet (IP) interface. The front panel of I0C4T (rear of VM600 rack) contains terminal strip connectors for connecting transmission cables from measurement chains (sensors and/or signal conditioners). Thread terminal connectors are also used to input and output all signals from any external control system. The I0C4T card has all input and output anti electromagnetic interference and surge protection functions, while meeting EMC (electromagnetic compatibility) standards. I0C4T connects the original dynamic (vibration) and velocity signals from the sensor to MPC4. These signals, once processed, are transmitted back to IOC4T and are available on the terminal strip of its front panel (behind VM600). For dynamic signals, four onboard analog-to-digital converters (dacs) provide calibration signal outputs within the range of 0 to 10 V. In addition, the four onboard voltage and current converters allow signals to be provided as current outputs in the range of 4 to 20 mA (jumper optional).
Vibro-meter    VM600 IOC16T   输入输出卡    通过连接器P2,使用工业包(IP)接口

Copyright © 2022 厦门雄霸电子商务有限公司漳州分公司 All Rights Reserved. 闽ICP备20016028号

厦门雄霸电子商务有限公司(漳州分公司)扫一扫咨询微信客服
厦门雄霸:何姗姗
Baidu
map