1756-EN2T 以太网通信模块1756-EN2T 支持 10 至 100 Mbps 的 EtherNet/IP 通信速率，并使用双绞线铜介质。它支持 256 个 Logix 和 128 个 TCP/IP 通信连接。它多可以支持 8 个轴，用于以太网/IP 网络上的集成运动，并在 5.1 伏直流电下消耗 1 A 电流。它的大功耗为 5.1 瓦，散热为 17.4 BTU/小时。它可以安装在 ControlLogix 机箱的任何插槽中。在接线方面，它使用非屏蔽 RJ45 5 类双绞线电缆连接器与控制器连接。要运行 EtherNet/IP 网络，必须定义 IP 地址、子网掩码、网关等参数。1756-EN2T 桥接器具有多种功能，例如为消息传递、分布式 I/O 和标记提供支持。它将消息封装在标准 TCP/IP 协议中。ControlNet 和 DeviceNet 网络协议允许它共享一个通用的应用层。它不需要任何调度或路由表来存储信息。其他功能包括保护模式、电子键控、设备级环形网络和并行冗余协议网络支持
The 1756-EN2T supports EtherNet/IP communication rates of 10 to 100 Mbps and uses twisted pair copper media. It supports 256 Logix and 128 TCP/IP communication connections. It can support up to 8 axes for integrated motion on Ethernet/IP networks and consumes 1 A of current at 5.1 V DC. It has a high power consumption of 5.1 watts and a heat dissipation of 17.4 BTU/hour. It can be installed in any slot of the ControlLogix chassis. In terms of wiring, it uses unshielded RJ45 Category 5 twisted pair cable connectors to connect to the controller. To run EtherNet/IP networks, parameters such as IP address, subnet mask, gateway, etc. must be defined. The 1756-EN2T bridge has multiple functions, such as providing support for messaging, distributed I/O, and tagging. It encapsulates messages in the standard TCP/IP protocol. The ControlNet and DeviceNet network protocols allow it to share a common application layer. It does not require any scheduling or routing tables to store information. Other features include protection mode, electronic keying, device level ring network, and parallel redundant protocol network support
SIS底板地址插头-SS4602
12槽底板-SE4601T07
底板终端-SE4604T04
12槽SIS底板-SS4601T07
SIS底板终端-SS4604T04
底板地址插头-SE4602
冗余-CIOC2-SE6504
AI模块-SE4003S2B4 16通道HART
AI模块-SE4003S2B1 8通道HART
LS AI模块-4-20mA RTD-SS4303T03
DI模块-SE4001S2T2B4 32通道
DO模块-SE4002S1T2B5 32通道
AI模块-SE4003S6B1 8通道RTD
LS AI模块-4-20mA 2W/4W-SS4303T01
LS AI模块-电偶 mV 带端子座-SS4303T52
AI模块-4-20mA 2W/4W-SE4303T01
AI模块-mV-SE4303T52
模块-LS DI 24-SS4301T02
扫一扫咨询微信客服
