SCHNEIDER 140CRP93100C RIO 头端适配器 是因为它允许您将跌落与主干电缆电气隔离

140CRP93100C    RIO 头端适配器

140CRP93100C您必须安装和使用 MA0185100 T 型连接器 10，因为系统上的每个 I/O 分支都需要它。之所以需要 T 型连接器，是因为它允许您将跌落与主干电缆电气隔离，并保护系统免受任何可能的阻抗匹配不正确的影响，除了阻抗问题外，140CRP93100C它还是可能的电缆断开的安。在干线电缆和每个 I/O 分线之间，所需的小信号强度为 14 dB。

当中继上的信号穿过 T 型连接器时，它的损耗小于 1db。前端RIO CPU的总分贝可能为35 dB。布线系统的整体性不得超过此允许的体系结构限制。

如果您的系统需要高可用性，140CRP93100C施耐德电气可以针对该问题提供解决方案;利用冗余电缆，这些电缆可防止电缆断裂。它还可以防止任何可能损坏的连接器。这样，当主机和每个分支之间连接两根电缆时，140CRP93100C您可以在第 一根电缆中断开，并且该中断不会中断您的通信。如果您碰巧有电缆断裂，当发生这种情况时，您会注意到状态位设置为 1。

这将向您表明存在问题、140CRP93100C掉线或电缆存在某种故障。如果您对预防性维护感兴趣，您会发现系统还提供计数器值。这适用于所有丢弃的所有通信事务。如果您在任何特定压线的电缆上发现高计数器值，这可能表明连接存在问题。有了这种高度的远见卓识，您将能够确定将纠正问题的工作，然后能够在处理不必要的停机时间之前启动预定的时间做出反应。140CRP93100C这为您节省了成本。节省时间和精力将不可避免地为您节省经济成本。

140CRP93100C You must install and use MA0185100 T-connector 10 because it is required for every I/O branch on the system. The reason why a T-connector is needed is because it allows you to electrically isolate the drop from the main cable and protect the system from any possible impedance matching errors. In addition to impedance issues, 140CRP93100C is also a safety net for possible cable disconnection. The minimum required signal strength between the trunk cable and each I/O branch is 14 dB.
When the signal on the relay passes through the T-connector, its loss is less than 1dB. The total decibel of the front-end RIO CPU may be 35 dB. The integrity of the wiring system shall not exceed the allowable architectural limitations.
If your system requires high availability, 140CRP93100C Schneider Electric can provide a solution to this problem; By utilizing redundant cables, these cables can prevent cable breakage. It can also prevent any potentially damaged connectors. In this way, when two cables are connected between the host and each branch, you can disconnect 140CRP93100C from the first cable without interrupting your communication. If you happen to have a cable break, you will notice that the status bit is set to 1 when this happens.
This will indicate to you that there is a problem, 140CRP93100C is disconnected, or there is some kind of cable malfunction. If you are interested in preventive maintenance, you will find that the system also provides counter values. This applies to all discarded communication transactions. If you find high counter values on any specific cable that is crimped, it may indicate a connection issue. With this high level of foresight, you will be able to identify the work that will correct the problem, and then be able to initiate a predetermined response time before dealing with unnecessary downtime. 140CRP93100C This saves you costs. Saving time and energy will inevitably save you economic costs.

RH102AM (X440-G2 managed switch) provides 24 Tri-speed 10/100/1000Base-T ports with RJ45 connectors, and four SFP 1000Base-X uplink (ISL) Gigabit (SFP1) ports (located on the back of
the unit), with a total of 28 active ports. The four (SFP) ports can be populated with 1000Base-X,
100Base-FX (P0973JE) or 100/1000Base-TX (RH102AL) MGBIC connector modules.
RH102AN (X440-G2 managed switch) provides 24 100Base-FX ports with LC connectors and four
(4) 1000Base-X (SFP) ports, with a total of 28 active ports. The four (SFP) ports can be populated
with 1000Base-X, or 100/1000Base-TX (RH102AL) MGBIC connector modules.
RH102AP (X440-G2 managed switch) provides 12 Tri-speed 10/100/1000Base-T ports with RJ-45
connectors, eight (8) 100Base-FX ports with LC connectors, and four (4) (SFP) ports. The four SFP
ports can be populated with 1000Base-X, or 100/1000Base-TX (RH102AL) MGBIC connector
modules.
RH102AQ (X440-G2 managed switch) provides 12 Tri-speed 10/100/1000Base-T ports with RJ45 connectors, and four (SFP+) ports, with a total of 16 active ports. The four (SFP+) ports can be
populated with 1000Base-X, or 100/1000Base-TX (RH102AL) MGBIC connector modules.
RH102AY (X440-G2 managed switch) provides 24 Tri-speed 10/100/1000Base-T ports with RJ-45
connectors, four (4) of which are combo ports (copper or SFP) and four (4) SFP+ ports (located on
the back of the unit). The four (SFP+) ports can be populated with 1000Base-X, or 100/1000BaseTX (RH102AL) MGBIC connector modules.